Truck runs and drives very good. 62k verified miles on The LS with All new wiring throughout. The engine compartment is super clean, Professionally done and tuned just right. Transmission is a 4L60 shifts perfect. Interior is very clean as you can see. Paint is not perfect with several chips here and there I would say it's great driver quality. Brand New Borla Dual Exhaust. Upper and lower moldings show their age must be originals. No rust on the rockers Cab corners are Solid. Wheels tubs look new with spray on liner on the bed only. All new body bushings through out. New outer Grill and insert, New Chrome bumpers, New side mirrors, New dashpad, Carpet, New inner doorpanels, HD headlights, All lights work as they should. New Original looking radio w Aux, New instrument cluster bezel, Speedo and gas gauge don't work . Wheels are 20x10 Intro Vistas with 315/35/20 Toyo Proxes 20x8.5 with 275/45/20 front tires. All 4 ball joints replaced 1/16/2017 and aligned as well. Truck is lowered 2in all around and feels just right. It has a Cowl Hood. New Headers, New Billet Steeringwheel. This Truck really moves! C10 is located at our dealership-Call or stop by today!
The things were doing to the truck currently Check all lugnuts, Top off all fluids, full detail, installing new rear iew mirror, correcting the all gauges to function along with horn.
A new, more modern look came in 1967, along with a new nickname: "Action Line". It was with this revision of the C/K truck that General Motors began to add comfort and convenience items to a vehicle line that had previously been for work purposes alone. Updated styling features for the 1967 Chevy Pickup trucks came with new body sheet metal that helps fight rust. The majority of 10 and 20 series Chevrolet trucks from 1967 to 1972 were built with a coil spring trailing arm rear suspension, which greatly improved the ride over traditional leaf springs. However, the leaf spring rear suspension was still available on those trucks, and standard on 30 series trucks. The front suspension on all Chevrolet trucks were independent front suspension with coil springs. GMC models came standard with leaf springs with coils springs optional; all four-wheel drive models (Chevrolet and GMC) had leaf springs on both axles. 1967 was the only year for the "small rear window" (RPO A10 offered a large rear window as a factory option). The standard drivetrain came with a three-speed manual transmission and one of two engines; the 250 in3 straight six or the 283 cu in (4.6 L) V8. The optional transmissions were the four-speed manual, the Powerglide and the Turbo-Hydramatic 350 and 400. The 292 six and the 327 in3 V8 were the optional engines. The 1/2 ton trucks came with a 6 x 5.5inch bolt pattern, the 3/4 and 1 ton trucks came with an 8 x 6.5inch bolt pattern.
The most visible change in differentiating a 1968 from a 1967 was the addition of side-marker reflectors on all fenders. Also, the small rear window cab was no longer available (the C40 and C60 medium duty trucks retained the small window). The GMC grille was revised, with the letters "GMC" no longer embossed in the horizontal crossbar. Another addition was the Custom Comfort and Convenience interior package that fell between the Standard cab and CST cab options. In 1968, Chevrolet celebrated 50 years of truck manufacturing, and to commemorate, they released a 50th Anniversary package, which featured an exclusive white-gold-white paint scheme. Also in 1968, the Longhorn model debuted on 3/4 ton trucks. Featuring a 133-inch wheelbase identical to the one-ton vehicles, it added an extra 6 inches to the bed. Longhorns, interestingly, were only 2wd; no factory Longhorn 4x4 was built.
The 327 c.i. V-8 engine was enlarged in 1969 to 350 CID (stroke increased from 3.25 to 3.48) with a net horsepower rating of 195-200, depending on emissions package 255 hp (190 kW), 350 cu in (5.7 L). Along with the new engines came a new grille design for Chevrolet trucks and a more upright hood for both Chevrolet and GMC trucks. A utility variant, known as the K5 Blazer, was also introduced with a shorter wheelbase of 104 inches (2,642 mm). The GMC version, known as the Jimmy, was introduced the same year. Some internal cab changes were also made, most notably the switch from a hand-operated parking brake to a foot pedal, and a more modern looking two-spoke steering wheel with plastic horn button replaced the previous year's three-spoke wheel with chrome horn button. Also new this year were upper and lower side moldings, which added another two-tone paint option. These were standard on CST trucks, and optional in any other trim level.
The only noticeable change for 1970 was a minor update to the Chevrolet grille. At first glance, the 1969 and 1970 grilles look very similar. However, the 1970s plastic inserts actually have highlights that divide the appearance into six separate sections. The 396, while still sold as such, was enlarged to 402 cubic inches starting in 1970.
Numerous changes occurred in 1971. First came another new grille design (the "egg crate") for Chevrolet trucks and black paint over portions of the GMC grille. Second, an additional trim package was introduced: the Cheyenne. On GMC models, this was referred to as the Sierra. These packages consisted mostly of comfort features nicer interiors, more padding and insulation, carpet, chrome trim, and upper and lower side molding and tailgate trim. 1971 was the first year for AM/FM radios factory installed. Finally, the front brakes on all light-duty trucks were switched from drum brakes to disc brakes, resulting in much less brake fade under heavy use. While many prior C/K half-ton trucks had used a six-lug bolt pattern (6 x 5.5") for the wheels, two-wheel-drive models switched to a five-lug pattern (5 x 5inch bolt circle) common to Buick, Oldsmobile, Pontiac, and Cadillac passenger cars. The 1/2 ton 4 x 4 retained the 6 lug bolt pattern. This bolt pattern would remain the standard through the end of the C/K series (along with the Chevrolet/GMC vans). The one ton (C30) trucks had the 8 x 6.5" pattern. Also, Chevrolet changed the 396 V8 emblem designation to 400 V8.
The 1972 models were virtually similar to the 1971 models, with the only change being the rear view mirror was glued to the windshield rather than bolted to top of the cab, and metal or vinyl-covered flat door panels were no longer available; all trim level door panels were molded plastic with integral armrests and wood grain inserts on Cheyenne and Sierra trim levels. For restoration, it should also be noted that the door and window cranks were slightly longer due to the molded plastic door panels, and the vent windows were now secured with a single screw on the inside of the door, thus differentiating it from the 1971 model year.